 |
 |
|
|
||||||||||||||||||||||
 |
|
|
|
Type: FLUSHITE Door & Panels: Doors and Panels shall be 1" thick insulated with a sound deadening honeycomb core. Face plates shall be not less than 22 gauge bonderized-galvanized steel and shall have a molding interlocking all edges. Door edges shall be welded at intervals around perimeter to insure a rigid unit. Corners shall be welded and ground smooth. Panels available in 20 gauge. Pilasters: Pilasters shall be 1-1/4" constructed of 20 gauge bonderized-galvanized steel insulated with a sound deadening double faced honeycomb core. Edges shall be welded at intervals around perimeter to insure a rigid unit. Edges to be interlocked with molding, corners to be welded and ground smooth. Hardware: Compartment is to be complete with all hardware and fastenings for a complete installation. Hardware to include wrap around door hinges, latch, stop and keeper and coat hook. Lower hinge to be recessed in the door and shall operate on opposing nylon cams. Upper hinge to be recessed in the door and shall operate on a pin anchored above and below the hinge bracket. Latch to be concealed type with emergency access features. All hardware to be Zamac chrome plated. Fittings: Wall and U brackets to be chrome plated. Door strikes and hinges to be fastened by means of "one-way" head tamper proof chrome plated sex bolts. All other screws to be Philips Head chrome plated. All pilasters to have a 3" high stainless steel shoe. Brass and stainless steel hardware available at additional cost. Finish: Partitions shall be cleaned and finish shall consist of highest quality powder coating baked at 350° F to insure a smooth protective finish. Color: As selected from color guide. *Custom colors available at additional cost.
Type: FLUSHITE Door & Panels: Door & Panels shall be constructed of a sandwich of laminated plastic bonded under pressure to a solid particle board core with the highest quality adhesive assuring a rigid, permanent bond. Doors and Panels – Finish thickness 1". Pilasters: The anchoring device shall consist of a levelling device fastened to bottom of pilaster and attached to the floor. Pilasters shall be constructed of a sandwich of laminated plastic bonded under pressure to a solid particle board core. Pilaster shall be 1-1/4" thick. Hardware: All hardware shall be heavy nonferrous chrome plated castings. Fastenings by means of thru-bolts with theft proof heads. Pilaster shoe shall be 4" high, of #302, 18-8 polished stainless steel. Includes all necessary hardware and fittings for a complete installation. Brass and Stainless Steel hardware available at additional cost. Surfacing: All faces and edges shall be 1/16" general purpose laminated plastic. All in accordance with NEMA standards. Finish: Laminated plastic shall be as selected from Flush-Metal's standard plastic colors and patterns. Color: As selected from color guide.
Type: FLUSHITE Door & Panels: Door & Panels shall be 1" thick insulated with a honeycomb core. Face plates shall be not less than 22 gauge stainless steel and shall have a molding interlocking all edges. Door edges shall be welded at intervals around perimeter to insure a rigid unit. Corners shall be welded and ground smooth. Panels available in 20 gauge. Pilasters: Pilasters shall be 1-1/4" constructed of 20 gauge steel insulated with a sound deadening honeycomb core. Edges shall be welded at intervals around perimeter to insure a rigid unit. Edges to be interlocked with molding corners to be welded and ground smooth. 3/8" stud bolts shall be furnished for fastening to concrete. Hardware: Compartment is to be complete with all hardware and fastenings for a complete installation. Hardware to include wrap around door hinges, latch, stop and keeper and coat hook. Lower hinge to be recessed in the door and shall operate on opposing nylon cams. Upper hinge shall operate on a pin anchored above and below the hinge bracket. Latch to be concealed type with emergency access features. All hardware to be Zamac chrome plated. Fittings: Wall and U brackets to be chrome plated. Door strikes and hinges to be fastened by means of "one-way" head tamper proof chrome plated sex bolts. All other screws to be Philips Head chrome plated. All pilasters to have a 3" high stainless steel shoe. Brass and Stainless Steel hardware available at additional cost. Finish: All stainless steel units shall be #4 finish and shall be vinyl covered for protection during shipment and installation. Color: Finish shall be #304 stainless steel, #4 finish.
Type: FLUSHITE Door & Panels: Doors shall be a minimum 3/4" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Panels shall be minimum 1/2" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Pilasters: The anchoring device shall consist of 3/8" x 1" steel bar mechanically fastened to bottom of pilaster and attached to floor by two 3/8" diameter steel stud bolts, nuts and expansion shields with a minimum penetration of 2" into concrete. Pilasters shall be a minimum 3/4" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Hardware: All hardware shall be heavy nonferrous chrome plated castings. Fastenings by means of thru-bolts with tamper proof heads. Pilaster shoe shall be 3" high, of #302, 18-8 polished stainless steel. Includes all necessary hardware and fittings for a complete installation. Brass and Stainless Steel hardware available at additional cost. Finish: Finish shall be matte finish of manufacturer's standard high pressure melamine color. Color: Finish shall be laminated plastic as selected from Flush-Metal's standard plastic colors and patterns. |
|
|
|
 |
|
|
|
|
|
|
|
 |
||||||
|
Type: FLUSHART Door & Panels: Doors and Panels shall be 1" thick insulated with a sound deadening honeycomb core. Face plates shall be not less than 22 gauge bonderized-galvanized steel and shall have a molding interlocking all edges. Door edges shall be welded at intervals around perimeter to insure a rigid unit. Corners shall be welded and ground smooth. Panels available in 20 gauge. Pilasters: Pilasters shall be 1-1/4" constructed of 20 gauge bonderized-galvanized steel insulated with a sound deadening double faced honeycomb core. Edges shall be welded at intervals around perimeter to insure a rigid unit. Edges to be interlocked with molding, corners to be welded and ground smooth. Hardware: Compartment is to be complete with all hardware and fastenings for a complete installation. Hardware to include wrap around door hinges, latch, stop and keeper and coat hook. Lower hinge to be recessed in the door and shall operate on opposing nylon cams. Upper hinge to be recessed in the door and shall operate on a pin anchored above and below the hinge bracket. Latch to be concealed type with emergency access features. All hardware to be Zamac chrome plated. Fittings: Wall and U brackets to be chrome plated. Door strikes and hinges to be fastened by means of "one-way" head tamper proof chrome plated sex bolts. All other screws to be Philips Head chrome plated. All pilasters to have a 3" high stainless steel shoe. Brass and stainless steel hardware available at additional cost. Finish: Partitions shall be cleaned and finish shall consist of highest quality powder coating baked at 350° F to insure a smooth protective finish. Color: As selected from color guide. *Custom colors available at additional cost. Type: FLUSHART Door & Panels: Door & Panels shall be constructed of a sandwich of laminated plastic bonded under pressure to a solid particle board core with the highest quality adhesive assuring a rigid, permanent bond. Doors and Panels – Finish thickness 1". Pilasters: The anchoring device shall consist of a levelling device fastened to bottom of pilaster and attached to the floor. Pilasters shall be constructed of a sandwich of laminated plastic bonded under pressure to a solid particle board core. Pilaster shall be 1-1/4" thick. Hardware: All hardware shall be heavy nonferrous chrome plated castings. Fastenings by means of thru-bolts with theft proof heads. Pilaster shoe shall be 4" high, of #302, 18-8 polished stainless steel. Includes all necessary hardware and fittings for a complete installation. Brass and Stainless Steel hardware available at additional cost. Surfacing: All faces and edges shall be 1/16" general purpose laminated plastic. All in accordance with NEMA standards. Finish: Laminated plastic shall be as selected from Flush-Metal's standard plastic colors and patterns. Color: As selected from color guide. Type: FLUSHART Door & Panels: Door & Panels shall be 1" thick insulated with a honeycomb core. Face plates shall be not less than 22 gauge stainless steel and shall have a molding interlocking all edges. Door edges shall be welded at intervals around perimeter to insure a rigid unit. Corners shall be welded and ground smooth. Panels available in 20 gauge. Pilasters: Pilasters shall be 1-1/4" constructed of 20 gauge steel insulated with a sound deadening honeycomb core. Edges shall be welded at intervals around perimeter to insure a rigid unit. Edges to be interlocked with molding corners to be welded and ground smooth. 3/8" stud bolts shall be furnished for fastening to concrete. Hardware: Compartment is to be complete with all hardware and fastenings for a complete installation. Hardware to include wrap around door hinges, latch, stop and keeper and coat hook. Lower hinge to be recessed in the door and shall operate on opposing nylon cams. Upper hinge shall operate on a pin anchored above and below the hinge bracket. Latch to be concealed type with emergency access features. All hardware to be Zamac chrome plated. Fittings: Wall and U brackets to be chrome plated. Door strikes and hinges to be fastened by means of "one-way" head tamper proof chrome plated sex bolts. All other screws to be Philips Head chrome plated. All pilasters to have a 3" high stainless steel shoe. Brass and Stainless Steel hardware available at additional cost. Finish: All stainless steel units shall be #4 finish and shall be vinyl covered for protection during shipment and installation. Color: Finish shall be #304 stainless steel, #4 finish. Type: FLUSHART Door & Panels: Doors shall be a minimum 3/4" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Panels shall be minimum 1/2" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Pilasters: The anchoring device shall consist of 3/8" x 1" steel bar mechanically fastened to bottom of pilaster and attached to floor by two 3/8" diameter steel stud bolts, nuts and expansion shields with a minimum penetration of 2" into concrete. Pilasters shall be a minimum 3/4" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Hardware: All hardware shall be heavy nonferrous chrome plated castings. Fastenings by means of thru-bolts with tamper proof heads. Pilaster shoe shall be 3" high, of #302, 18-8 polished stainless steel. Includes all necessary hardware and fittings for a complete installation. Brass and Stainless Steel hardware available at additional cost. Finish: Finish shall be matte finish of manufacturer's standard high pressure melamine color. Color: Finish shall be laminated plastic as selected from Flush-Metal's standard plastic colors and patterns. |
||||||
 |
||||||
 |
||||||
|
Type: FLUSHUNG Door & Panels: Doors and Panels shall be 1" thick insulated with a sound deadening honeycomb core. Face plates shall be not less than 22 gauge bonderized-galvanized steel and shall have a molding interlocking all edges. Door edges shall be welded at intervals around perimeter to insure a rigid unit. Corners shall be welded and ground smooth. Panels available in 20 gauge. Pilasters: Pilasters shall be 1-1/4" constructed of 20 gauge bonderized-galvanized steel insulated with a sound deadening double faced honeycomb core. Edges shall be welded at intervals around perimeter to insure a rigid unit. Edges to be interlocked with molding, corners to be welded and ground smooth. Hardware: Compartment is to be complete with all hardware and fastenings for a complete installation. Hardware to include wrap around door hinges, latch, stop and keeper and coat hook. Lower hinge to be recessed in the door and shall operate on opposing nylon cams. Upper hinge to be recessed in the door and shall operate on a pin anchored above and below the hinge bracket. Latch to be concealed type with emergency access features. All hardware to be Zamac chrome plated. Fittings: Wall and U brackets to be chrome plated. Door strikes and hinges to be fastened by means of "one-way" head tamper proof chrome plated sex bolts. All other screws to be Philips Head chrome plated. All pilasters to have a 3" high stainless steel shoe. Brass and stainless steel hardware available at additional cost. Finish: Partitions shall be cleaned and finish shall consist of highest quality powder coating baked at 350° F to insure a smooth protective finish. Color: As selected from color guide. *Custom colors available at additional cost. Type: FLUSHUNG Door & Panels: Door & Panels shall be constructed of a sandwich of laminated plastic bonded under pressure to a solid particle board core with the highest quality adhesive assuring a rigid, permanent bond. Doors and Panels – Finish thickness 1". Pilasters: The anchoring device shall consist of a levelling device fastened to bottom of pilaster and attached to the floor. Pilasters shall be constructed of a sandwich of laminated plastic bonded under pressure to a solid particle board core. Pilaster shall be 1-1/4" thick. Hardware: All hardware shall be heavy nonferrous chrome plated castings. Fastenings by means of thru-bolts with theft proof heads. Pilaster shoe shall be 4" high, of #302, 18-8 polished stainless steel. Includes all necessary hardware and fittings for a complete installation. Brass and Stainless Steel hardware available at additional cost. Surfacing: All faces and edges shall be 1/16" general purpose laminated plastic. All in accordance with NEMA standards. Finish: Laminated plastic shall be as selected from Flush-Metal's standard plastic colors and patterns. Color: As selected from color guide. Type: FLUSHUNG Door & Panels: Door & Panels shall be 1" thick insulated with a honeycomb core. Face plates shall be not less than 22 gauge stainless steel and shall have a molding interlocking all edges. Door edges shall be welded at intervals around perimeter to insure a rigid unit. Corners shall be welded and ground smooth. Panels available in 20 gauge. Pilasters: Pilasters shall be 1-1/4" constructed of 20 gauge steel insulated with a sound deadening honeycomb core. Edges shall be welded at intervals around perimeter to insure a rigid unit. Edges to be interlocked with molding corners to be welded and ground smooth. 3/8" stud bolts shall be furnished for fastening to concrete. Hardware: Compartment is to be complete with all hardware and fastenings for a complete installation. Hardware to include wrap around door hinges, latch, stop and keeper and coat hook. Lower hinge to be recessed in the door and shall operate on opposing nylon cams. Upper hinge shall operate on a pin anchored above and below the hinge bracket. Latch to be concealed type with emergency access features. All hardware to be Zamac chrome plated. Fittings: Wall and U brackets to be chrome plated. Door strikes and hinges to be fastened by means of "one-way" head tamper proof chrome plated sex bolts. All other screws to be Philips Head chrome plated. All pilasters to have a 3" high stainless steel shoe. Brass and Stainless Steel hardware available at additional cost. Finish: All stainless steel units shall be #4 finish and shall be vinyl covered for protection during shipment and installation. Color: Finish shall be #304 stainless steel, #4 finish. Type: FLUSHUNG Door & Panels: Doors shall be a minimum 3/4" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Panels shall be minimum 1/2" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Pilasters: The anchoring device shall consist of 3/8" x 1" steel bar mechanically fastened to bottom of pilaster and attached to floor by two 3/8" diameter steel stud bolts, nuts and expansion shields with a minimum penetration of 2" into concrete. Pilasters shall be a minimum 3/4" thick solid phenolic core with high pressure melamine matte finish surface made as an integral part of the core material. Laminated surfaces are unacceptable. All edges are to be machined smooth. Hardware: All hardware shall be heavy nonferrous chrome plated castings. Fastenings by means of thru-bolts with tamper proof heads. Pilaster shoe shall be 3" high, of #302, 18-8 polished stainless steel. Includes all necessary hardware and fittings for a complete installation. Brass and Stainless Steel hardware available at additional cost. Finish: Finish shall be matte finish of manufacturer's standard high pressure melamine color. Color: Finish shall be laminated plastic as selected from Flush-Metal's standard plastic colors and patterns. |
||||||
|
|
|
|
|
HOME PAGE HISTORY PRODUCTS SPECIFICATIONS INSTALLATION GUARANTEE CONTACT US |